[2023] Earn Quick And Easy Success With NACE-CIP1-001 Dumps
Free NACE-CIP1-001 pdf Files With Updated and Accurate Dumps Training
To be eligible for the NACE-CIP1-001 certification exam, candidates must have a minimum of six months of experience in the coating inspection industry. They must also complete a training program that covers the fundamental principles of coating inspection. The training program should be completed through a NACE-approved training provider and should include at least 80 hours of training.
NEW QUESTION # 40
ASTM Standards are applicable:
- A. In North America
- B. In the USA
- C. In Asia
- D. When specified
Answer: D
NEW QUESTION # 41
What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?
- A. 2.5 cm (1 inch)
- B. 1 cm (.39 inch)
- C. 6.35 cm (2.5 inch)
- D. 2.5 millimeters (.10 inch)
Answer: A
NEW QUESTION # 42
Due to a previous premature coating failure the owner has required the original coating applicator to return to remove and replace 10,000 square feet of a failed three coat system at the applicator's cost. Due to the financial implications of another failure, the owner has offered you the job as the NACE CIP Level 1 Coating Inspector and explained that he expects you to be his "insurance policy" for this job. You have never been involved in a warranty job before and are unfamiliar with the coating system.
Your preferred FIRST course of action is to:
- A. Review the Product Data Sheets, and conduct a walk thru of the job site prior to the pre-job Conference
- B. Meet with the owner and explain your limitations and concerns prior accepting the assignment
- C. Purchase Professional Liability Insurance prior to job commencement
- D. Review the Product Data Sheets and meet with the Coating Applicator 'prior to the pre-job meeting
Answer: A
NEW QUESTION # 43
Upon arrival of coating materials, the inspector should
- A. review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations.
- B. observe and document the amount of material and batch numbers.
- C. observe aryl document that the applicator WFT at regular intervals during application.
- D. observe and document time frame and environmental conditions between each coat.
Answer: B
NEW QUESTION # 44
A single application coating film has a measured dry film thickness (DFT) between 4 and 5 mils (between 100 and 125 microns). The volume solids of the coating immediately before application were 67%, What wet film thickness (WFT) was applied?
- A. 6 to 7 mils (150 to 175 microns)
- B. 5 to 6 mils (125 to 150 microns)
- C. 8 to 10 mils (200 to 250 microns)
- D. 10 to 12 mils (250 to 300 microns)
Answer: A
NEW QUESTION # 45
Prior to using Inspection Tools the inspector must:
- A. a), b) & c)
- B. Read the manufactures' instructions
- C. Be trained on how to use the instrument
- D. Ensure the instrument is within calibration parameters
Answer: A
NEW QUESTION # 46
An inspectors personal log book should contain:
- A. Objective comments regarding the application work
- B. The inspector's personal opinions of the application team
- C. No comments regarding the application team
- D. Subjective comments re ding the application team
Answer: C
NEW QUESTION # 47
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:
- A. Advise the Contractor he can proceed
- B. Call your supervisor
- C. Advise the Contractor of your readings
- D. Advise the Contractor he cannot proceed
Answer: C
NEW QUESTION # 48
Owners hire NACE Inspectors' with the expectation that:
- A. The Inspector will improve job flow and schedule
- B. The inspection cost will be offset by an improvement in service life
- C. The Inspector will make a meaningful technical contribution to the job
- D. a) and c)
Answer: D
NEW QUESTION # 49
NACE SP 0178 is a standard for:
- A. Tanks and Vessels to be Externally Coated
- B. Stainless steel pipe to be Externally Coated
- C. Tanks and Vessels to, be Lined for Immersion Service
- D. Structural steel to be coated for Atmospheric Service
Answer: C
NEW QUESTION # 50
When applying Thermal Spray Coatings the specification is most likely to refence:
- A. NACE SP 0178
- B. SSPC PA 2
- C. NACE SP 0188
- D. SSPC-CS 23.00/AWS C2.23/NACE No. 12
Answer: D
NEW QUESTION # 51
The Inspector's Log Book is generally:
- A. Shared with all parties upon project completion
- B. Submitted to the client upon project completion
- C. Retained by the inspector upon project completion
- D. Shredded by the inspector upon project completion
Answer: C
NEW QUESTION # 52
When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:
- A. Chloride salt may produce a false positive
- B. Ultra-Violet light may contaminant the surface
- C. Synthetic oil or grease may not be identified
- D. Presence of weld spatter may produce a false positive
Answer: C
NEW QUESTION # 53
Surface profile describes:
- A. The initial condition of the surface prior to abrasive blasting
- B. The level of surface roughness required after abrasive blasting
- C. The level of surface cleanliness required after abrasive blasting
- D. The general condition of the surface required after abrasive blasting
Answer: B
NEW QUESTION # 54
In a non-convertible coating the role of the primary solvent is to:
- A. To dissolve the resin
- B. To control the evaporation rate
- C. To make the coating flow out better
- D. To promote faster cure
Answer: B
NEW QUESTION # 55
Excessive working of the surface with a power grinder can be detrimental because excessive burnishing
- A. develops a polished surface, which is a poor anchor profile for most coatings
- B. develops a good anchor profile resulting in uneven coating application.
- C. damages structural elements thereby speeding up the corrosion process.
- D. scratches the surface too deeply resulting in uneven coating application
Answer: A
NEW QUESTION # 56
Polymerization is the process of:
- A. Monomers joining together
- B. All thermoplastic coatings
- C. All organic coatings
- D. Monomers telegraphing
Answer: A
NEW QUESTION # 57
Daily reports are important because:
Select All That Apply
- A. Inspectors rarely change on a project.
- B. The information aids communication with supervisors.
- C. Management uses them to make personnel decisions.
- D. the information impacts future projects.
Answer: B,C,D
NEW QUESTION # 58
If inspectors identify issues of non-conformance during an inspection, they should
- A. instruct the contractor's personnel in how to correct the issue so the project is not delayed
- B. perform additional tests secretly to ensure there are no other potential issues at the site
- C. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
- D. wait until the final report is being prepared to identify the issues in writing so they are fully documented
Answer: C
NEW QUESTION # 59
The Inspector should record the serial numbers of inspection instruments:
- A. Only if the specification requires it
- B. Each time the instrument is used
- C. Only if the instrument is suspected of not working properly
- D. Only when verifying accuracy of the instrument
Answer: B
NEW QUESTION # 60
Whenever dissimilar metals must join, the most common practice is to
- A. provide cathodic protection to prevent corrosion,
- B. coat all connected dissimilar metals.
- C. avoid coating all connected dissimilar metals.
- D. provide anodic protection to prevent corrosion.
Answer: B
NEW QUESTION # 61
Galvanic corrosion occurs on which of the following substrates:
- A. Wood
- B. Fiberglass Reinforced Plastic
- C. Metal
- D. Concrete
Answer: C
NEW QUESTION # 62
Inspector's daily reports are used:
Select All That Apply
- A. To aid in arbitration between the contractor and client
- B. To provide continuity between inspectors
- C. To help in cases of a coating failure
- D. By the contractor to estimate the amount of work done that day
Answer: A,B,C,D
NEW QUESTION # 63
......
Real Updated NACE-CIP1-001 Questions Pass Your Exam Easily: https://freetorrent.dumpstests.com/NACE-CIP1-001-latest-test-dumps.html